What does ee2 mean in Toyostove?

The EE2 code means that the flame sensor did not detect a flame during the ignition and pre-heat stage. The EE6 code means that the flame sensor has lost flame contact twice after the unit reached the normal burning stage. EE2 Failure During Ignition.

An EE 2 or EE 6 can be an indication it is time to service the stove (Clean burner assembly, heat chamber, heat exchanger, and exhaust fan (L56, 60, 73); Replace burner mat (Laser 73) or burner coating (all other models) and gaskets.) Warning: Do not use coating in Toyostove Laser 73. The coating will cause the burner.

how does a Toyostove work? The Toyostove Laser 73 is a sealed combustion or direct-vent system that uses only outside air for combustion and vents combustion gases directly to the outdoors. This modern high-efficiency model provides safe, comfortable warmth for zone heating or whole house heat. Allow a few moments to load.

Accordingly, how do you bleed a Toyostove?

10 Steps to Bleed & Restart Your Furnace after Running Out of Heating Oil

  1. Step 1: Fill the Fuel Tank.
  2. Step 2: Hit the Reset Button.
  3. Step 3: Turn off the Furnace.
  4. Step 4: Collect Your Tools.
  5. Step 5: Find the Bleeder Valve.
  6. Step 6: Attach Nylon Tubing.
  7. Step 7: Turn on the Furnace and Unscrew the Valve.
  8. Step 8: Tighten the Valve.

Can I put diesel in my oil furnace?

If you do run out of heating oil for your furnace, you can make your way to any gas station that sells diesel and put the diesel fuel in your oil tank. Both of these can be used in your furnace without a problem, and they will burn just as good, if not better than some heating oil that is available today.

How do I reset my Beckett oil burner?

How to Prime a Beckett Oil Burner Turn up your thermostat to ignite the burner. Press and hold the “Reset” button for 15 seconds or until the yellow light turns on. Press and release the “Reset” button again quickly, while the igniter is active, to prime the pump. Purge or bleed the pump until all bubbles and froth are eliminated.

What happens when furnace runs out of oil?

Running out of heating oil can cause the furnace to build up sludge which clogs the filter and prevents the heating system from working properly. Sludge occurs when too much dirt, dust, or grime settles in your oil tank, typically at the bottom.

Why do I have to keep bleeding my furnace?

When to Bleed a Furnace This most common cause of having to bleed an oil furnace is running out of oil. Air enters into the supply line when an oil tank runs dry. When the tank is then filled up, the supply line forms an air lock that blocks the oil from flowing.

What to do if you run out of heating oil?

Follow this guide to know what to do when your heating fuel runs out! Step 1: Call the Heating Oil Company. Obviously, the first thing you should do when you deplete your heating oil supply is to call your heating oil company for a refill. Step 2: Get Some Diesel. Step 3: Fill Up Your Oil Tank. Step 4: Restart the Furnace.

How do I purge the air in my radiant heating system?

By holding the end of the discharge hose under water in the 5-gallon bucket, stray bubbles are impossible to miss. Close the shut off valve. Attach a second garden hose to the fill valve. You are now ready to purge the air out of zone #1. Using full house pressure or a powerful utility pump, flood the zone.

How do you bleed a Firebird boiler?

The bleed nut is shown clearly and, using an allen key, it is easy to loosen it to allow the trapped air to escape. When all the air has escaped some fuel will start to leak out, once this happens, re-tighten the nut. Press the red restart button and the boiler should restart, you might have to press it a few times.

How do I light the pilot on my oil furnace?

Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.