How do I make my gas fireplace flame bigger?

Turn the key valve counterclockwise as far as it will turn to open the gas line. Start the fire by following your gas fireplace lighting instructions. Turn the gas control knob to high to increase the flames in your fireplace if applicable.

Typically low flame height is caused by one of three things. Either you have low gas pressure at the fireplace or you need to restrict the venting to slow down the draft. 1) It is common to think that the gas pressure is fine when this only one appliance on the line or the meter is turned all the way up.

Similarly, what color should the flame be on a gas fireplace? A healthy gas flame will burn steadily with a yellow or orange. If the flame is not yellow or orange it may be a sign that your gas fireplace needs adjusting or cleaning, which should be done by a qualified technician, such as those we have at Kozy Heat.

Also to know, how high should the flames be on a gas fireplace?

Turn the burner on and set the flame height to high. Take a reading. This time, you want to see an ideal reading of 3.5 inches or the pressure rating indicated in the manual. Don’t forget to turn off the burner and the gas and then tighten the screw again.

What should a gas fireplace flame look like?

The burner flames from your natural gas furnace should look blue or almost completely blue. A healthy natural gas furnace flame is characterized by a roaring blue flame with a light blue triangle in its center. There may be a tiny tip of yellow.

Can you adjust the pilot light on a gas fireplace?

In either case, adjusting the pilot light is fairly easy. You’ll just need a screwdriver and a little patience, and you can fix the issue in a matter of minutes. First, locate the controls on the bottom of a direct-vent fireplace. On others, there will be a screw that you can easily adjust with a screwdriver.

How can I make my gas fireplace more realistic?

Gas Log Embers Just place of few of the Platinum Bright Embers throughout the fireplace to create an even more vibrant glow. If you have vented gas logs, place small pieces on the burner bed to create a realistic glowing effect wherever the flame flows through the fiber material.

Can a pilot light flame be adjusted?

Adjusting the Pilot Flame If the pilot flame is too small, you may be able to make it larger by turning the pilot adjustment screw on the valve control counterclockwise with a screwdriver to open it. The cause of a weak flame may also be an obstruction in the pilot tube.

Is it safe to run a gas fireplace all day?

There is no time limit built into the safety requirements for vented gas fireplaces. Gas fireplaces literally run for days when being safety tested. However, unvented gas fireplaces (aka vent free, ventless) can adversely affect indoor air quality and shouldn’t be used more than a few hours at a stretch.

Should gas fire flames be blue or yellow?

A blue flame indicates that the burner is providing an air-fuel mix with sufficient oxygen for complete combustion right out of the nozzle. A yellow or orange flame indicates that the burner is providing only enough oxygen to partially react with the fuel, leaving some unconsumed carbon in the flame.

How do you control the flame on a gas fireplace?

How to Adjust a Gas Log Fireplace Flame Locate the gas log control knob. Light the gas logs by turning the control knob to the “pilot” setting. Release the control knob and allow the flame to burn for one minute. Locate the switch at the front of the gas logs marked “on.” Move the switch to the “on” setting to ignite the burners below the gas logs.

Should gas fireplace flames Be Blue?

A gas fire blue flame when the fire is initially turned on is quite normal. If your gas fire is blue with orange tips this is also quite acceptable as it’s often temporary due to dust in air particles, or a possible lack of oxygen. Colours of flames in gas fires may range from a yellow gas flame, through orange to red.

Do gas fireplaces need to be serviced?

Gas fireplaces are easy and convenient. So much so, that it’s easy to forget that even a gas fireplace needs upkeep every once in a while. To keep your gas fireplace operating safely and in tip-top shape, it’s recommended to perform annual maintenance.

Where is the pilot light adjustment screw?

The pilot adjustment screw is located on the gas valve, just “above” the pilot tube (See Figure 3). Remove the cap screw and find the actual adjustment screw behind it. Turn the screw in to decrease pilot flame, out to increase.